Czech
Device COMPACT - F1 do 40 bar
1.3
Catalog sheet: 1.3
The device COMPACT F-1 may be used for special works on pipelines as under media positive pressure. Pipelines are drilled using closing fittings.
The device COMPACT F-1 may be used for special works on pipelines as under media positive pressure. Pipelines are drilled using closing fittings.
The drilling rod gets through the drilling body with sealing elements axial shift and drilling rod locking mechanism. In its working part, the drilling rod is adapted for the fixing of the drilling bit and a centering pilot. In its control sections, it is provided with a square end that allows for manual or machine drilling.
The drilling body has in its bottom part a special ending flange with openings for the fixing of a stabilizing frame and for the mounting of the drilling body to the flange or adapter chamber. The stabilization frame provides for the guiding of the drilling rod and its safe retraction after the completion of the drilling of the opening. If necessary, the guiding rods of the stabilization frame may be extended (following the sheet the sheet 1.3-2).
The devices are designed so that all works including the closing of a drilled opening in the pipeline could be executed without any media leaks.
The device COMPACT F-1 up to 40 bar is designed and manufactured as a kit system that allows for a high level of variability. Normally, it is supplied as the below described sets or customized sets individually set up base on customer´s requirements.
The drilling rod gets through the drilling body with sealing elements axial shift and drilling rod locking mechanism. In its working part, the drilling rod is adapted for the fixing of the drilling bit and a centering pilot. In its control sections, it is provided with a square end that allows for manual or machine drilling.
The drilling body has in its bottom part a special ending flange with openings for the fixing of a stabilizing frame and for the mounting of the drilling body to the flange or adapter chamber. The stabilization frame provides for the guiding of the drilling rod and its safe retraction after the completion of the drilling of the opening. If necessary, the guiding rods of the stabilization frame may be extended (following the sheet the sheet 1.3-2).
The devices are designed so that all works including the closing of a drilled opening in the pipeline could be executed without any media leaks.
The device COMPACT F-1 up to 40 bar is designed and manufactured as a kit system that allows for a high level of variability. Normally, it is supplied as the below described sets or customized sets individually set up base on customer´s requirements.
Diameter of pipeline drilled: no limit
Diameter of drilled opening:
18 - 200 mm (depending on the set outfit) *
Drilled pipeline material:
This depends on the used drilling bit and drilled material properties (metal, plastic, asbestos- concrete etc.)
Media:
Natural gas, water, non-aggressive gases or liquids. Other media should be consulted with the manufacturer
Maximum pressure in the drilled pipeline: do 40 bar
Working temperature: -50/+70°C **
* In case of use of accessory systems with regard to specific drilling conditions (adapting flanges, drilling bits etc.), based on consultation with the manufacturer, it is possible to drill openings up to the diameter of 480 mm.
** The bottom limit of the temperature range may be limited depending on measures taken to prevent freezing of condensate in the air system when using a compressed air motor drive, the upper limit may be increased based on consultation with the manufacturer.
** The bottom limit of the temperature range may be limited depending on measures taken to prevent freezing of condensate in the air system when using a compressed air motor drive, the upper limit may be increased based on consultation with the manufacturer.
| Item No. | Name | Catalogue No. |
| 1. | Drilling rods | sheet 1.4-2.1 |
| 2. | Drilling bit FKV (for steel) | sheet 1.4-2.2 |
| 3. | Centering pilots Ø 18 | sheet 1.4-2.3 |
| 4. | Chambers, adapters, fittings | sheet 1.4-2.3 |
| 5. | Guiding rod extension L500 | 132-2000-012 |
| 6. | Guiding rod connecting bolt | 132-2000-011 |
| 7. | Motor drives | sheet 1.4-2.5 |
Note:
Guiding rod extension (No. 5) is to be used for the extension of standard guiding rods of the set COMPACT-F1/VT (sheet 1.2-.1.1 No. 4) when using drilling rods 1400 mm and longer.